weber.sysWaterproof-it Shower 

Waterproof-it Shower is suitable for the waterproofing of shower cubicles prior to the fixing of ceramic, porcelain or natural stone tiles.

Suitable for interior and exterior use.

• Exceptional and consistent quality
• Can be used on a wide range of surfaces
• 24 hour setting time

The following materials are included in the drum :

2 x 5kg bags of Waterproof-it Compound (labelled Part A)

5 litre Waterproof-it Emulsion (labelled Part B)

1 roll of Waterproof-it Membrane (labelled Part C)

The following tools and accessories will be required:

• Builders block-brush
• Overall
• Rubber gloves

Depending on the nature and evenness of the surface and method of application, Part A mixed with Part B will cover approximately 6m² when applying two coats using a block-brush.

Suitable for use on surfaces like :

• Cement-based plaster
• Cement screeds
• Concrete surfaces
• Gypsum Board
• Cement  fibre board

The following minimum curing periods should be observed before application commences :

• New concrete floors : 28 days
• New screeds : 28 days
• New brick walls : 28 days
• New cement plaster : 28 days

The walls or floors to be tiled must be wood-floated and not steel-trowelled or power-floated. Ensure that all surfaces are clean, dry, sound and free from dust, grease or any contamination that could impair bonding.

Make good any unsound areas and remove flaky or peeling layers before tiling. Organic growth must be removed and the spores killed using household bleach.

Not suitable as a final finish or for use in direct sunlight. Not suitable for waterproofing exterior building walls, industrial floors or unstable surfaces.

Not suitable for tanking areas that are continually immersed, such as ponds and pools. Not suitable for waterproofing roofs and terraces. Not resistant to pressure washing on some substrates.

■ Combine the two 5kg bags of Part A with Part B and mix to a creamy slurry.

■ Allow the mixture to mature for 5 minutes and re-mix thoroughly. Do not add more water.

Ensure that the substrate is clean and dust-free.

• Apply a 1.5mm to 2mm thick layer of the Part A/B slurry to the substrate using a block-brush. Allow returns of at least 75mm on the vertical and horizontal surfaces, paying particular attention to the corners.
• Apply Part C onto the wet slurry and press down firmly. Allow the membrane joints to overlap by 100mm with neighbouring membrane. Brush out any air pockets.
• Immediately apply a second coat of slurry, ensuring that the Part C is completely saturated.
• Allow to dry for 24 hours before tiling commences.

See the Weber product guide for applicable adhesives and grouts.

Please note: Do not use this weber.sys Waterproofing system as the final finish.

Ensure that the substrate is clean and dust-free.

• Apply a 1.5mm to 2mm thick layer of the Part A/B slurry to the substrate using a block-brush. Allow returns of at least 75mm on the vertical and horizontal surfaces, paying particular attention to the corners.
• Apply Part C onto the wet slurry and press down firmly. Allow the membrane joints to overlap by 100mm with neighbouring membrane. Brush out any air pockets.
• Immediately apply a second coat of slurry, ensuring that the Part C is completely saturated.
• Allow to dry for 24 hours before tiling commences.

See the Weber product guide for applicable adhesives and grouts.

Please note: Do not use this weber.sys Waterproofing system as the final finish.

Mask all areas where there is a risk of splashing and staining and where straight edges are required. Masking tape must be removed before the material has dried.

weber.sys Waterproof-it Compound contains cement, which is alkaline when wet and can cause skin irritation. Use eye protection and gloves and avoid prolonged skin contact. Avoid inhalation of dust. Wash skin contamination away with warm soapy water. Remove splashes to the eyes by prolonged irrigation and consult a doctor. Do not ingest.

We agree that Weber products meet the product specifications and will be free from any defect. Any guarantee with regard to the performance of Weber products will be subject to the professional and practical application of Weber products in accordance with our instructions and specifications.

However, we have no influence over specific site conditions and therefore, if in doubt, the user should first carry out sufficient tests to ensure that the product is suitable. In special cases, obtain advice.

Should our product prove defective, we undertake to replace any defective material. This guarantee will fall away in the event of Weber products being contaminated by the addition of sand, cement or substance other than recommended by us.

Weber has a team of experienced advisors available to provide technical support.

Technical helpline : 0860 27 28 29 or visit www.weber-tylon.co.za

77 Ostend Road, Germiston South, Johannesburg Tel.: +27 11 345-5300 Fax: +27 11 345-5301 Sales : 0860 27 28 29 or visit www.weber-tylon.co.za

To the best of our knowledge and belief, this information is true and accurate. As the conditions of use and any labour involved are beyond our control, the end-user must satisfy himself by prior testing that the product is suitable for his specific application. Products are sold subject to our Standard Conditions of Sale.