Use
For grouting joints between quarry tiles:
- Suitable for walls and floors
- Suitable for interior and exterior use
- Suitable for intermittently wet and dry conditions
- Used in industrial kitchens, bathrooms and showers
Features & benefits
- Exceptional and consistent quality
- Suitable for walls and floors
- Suitable for joint widths up to 15mm
- Can be used in conjunction with under-tile heating
- Limited flexibility to accommodate some movement
Technical data
- Joint width: 4 to 15mm
- Pot life: 3 hours
- Final drying time: 24 hours at 20oC and 50% humidity
- Water demand: 4 litres per 20kg
- Application temperatures: Do not apply in temperatures below 5oC or above 30oC
Coverage
Use the following formulation to calculate the quantity of Weber.grout Quarry Grout required per square metre of tiling:
kg/m2 = (A +B / A x B) x C x D x 1.7
A = length of tile; B = width of tile; C = thickness of tile; D = average joint width
Surface preparation
The minimum joint width is 2mm for walls and 3mm for floors.
Do not butt-joint tiles.
Adhesive should be left to dry for at least 24 hours before grouting. If a rapid-set adhesive is used, kindly follow the manufacturer’s instructions.
Longer drying times may be required on sealed or impervious surfaces. Ensure that the tiles and joints are clean and free from grease or any other contamination.
It is advisable to moisten the joints before application to assist the flow of grout into the joints.
Mixing
- Tylon Quarry Tile Grout should be mixed with 1.35 litres of clean water per 5kg bag to produce a thick creamy paste.
- Allow the mixture to stand for 5 minutes.
- Remix thoroughly before use.
If Weber.grout Quarry Tile Grout is used in permanently wet areas, the water in the mix should be replaced with Tylon Bond-It. Mix as above.
Do not add too much water or attempt to extend the working time by adding more water as this will cause the set grout to be weak with a tendency to crumble.
It may also cause surface discolouration and variation, especially with darker colours.
Application
Using a squeegee or rubber float, apply Tylon Quarry Tile Grout liberally to a small area. Completely fill the joints leaving no voids. Excess grout should be removed immediately using the grout squeegee held at 90C to the tiles. Move the squeegee diagonally across the tiles to prevent removal of the grout within the joints. Leave the grouted joints to harden for approximately 45 minutes. The excess grout can then be cleaned off with a damp (not wet) sponge. Do not leave excess moisture on grout joints. The joints can be finished off by pointing along the joint lines. Allow the joints to dry for 2 hours before polishing with a clean, dry cloth.
Please note :
Some tiles may have a soft surface which can be scratched during grouting. Tiles with a matt or porous texture are prone to surface staining when coloured grouts are used. The use of an appropriate protective sealer is recommended before grouting. Natural stones such as limestone, marble, slate, sandstone and terracotta, will require sealing prior to grouting. Some tile faces have shallow depressions that can fill with grout. This grout must be removed before it hardens. When using a grout that is a similar colour to the tiles, it can be difficult to see any residue that is left in these shallow depressions. It is recommended that these tiles be treated with an appropriate protective sealer that helps to stop the grout sticking to the tile face. It is advisable to test the grout on a spare tile before proceeding.
Storage
When stored, unopened in a dry place at temperatures above 5oC, shelf life is 6 to 9 months from date of manufacture.
Safety instructions
Contains cement, which is alkaline when wet and can cause skin irritation. Use eye protection and gloves and avoid prolonged skin contact. Avoid inhalation of dust. Wash skin contamination away with warm soapy water. Remove splashes to the eyes by prolonged irrigation and consult a doctor. Do not ingest.
Guarantee
We agree that Weber products meet the product specifications and will be free from any defect. Any guarantee with regard to the performance of Weber products will be subject to the professional and practical application of Weber products in accordance with our instructions and specifications.
However, we have no influence over specific site conditions and therefore, if in doubt, the user should first carry out sufficient tests to ensure that the product is suitable. In special cases, obtain advice.
Should our product prove defective, we undertake to replace any defective material. This guarantee will fall away in the event of Weber products being contaminated by the addition of sand, cement or substance other than recommended by us.
Technical services
Weber has a team of experienced advisors available to provide technical support.
Technical helpline : 0860 27 28 29 or visit www.weber-tylon.co.za
Saint-Gobain Construction Products SA (Pty) Ltd
77 Ostend Road, Germiston South, Johannesburg Tel.: +27 11 345-5300 Fax: +27 11 345-5301 Sales : 0860 27 28 29 or visit www.weber-tylon.co.za
To the best of our knowledge and belief, this information is true and accurate. As the conditions of use and any labour involved are beyond our control, the end-user must satisfy himself by prior testing that the product is suitable for his specific application. Products are sold subject to our Standard Conditions of Sale.
Product information
Packaging
